2008年1月28日 星期一
臺灣陽傑科技LED路燈通過多項安全認證
近日,臺灣陽傑科技表示,其LED路燈分別通過美國UL、臺灣CNS、歐洲CE、大陸CQC的國際安全認證,為臺灣LED業界的首例,並首度證明HB LED照明燈具可以通過現有燈具安全標準。
陽傑科技LED路燈在防水、防塵、電子特性等專案,均通過多項國際照明燈具與景觀燈具安全規範,包含UL、CE、CQC、CNS等,分別代表美國、歐盟、大陸與臺灣的安全標章,成為第1家通過現有燈具安全規範的LED燈具廠商,有助於拓展歐美等先進國家市場。
陽傑科技採用LED燈具的主要散熱元件為回路熱管(LHP),具全球獨家專利,曾經過美國太空總署(NASA)的高規格檢驗通過,將LED熱能引導至燈具外殼,可使用於零-30度~ 50度的環境,具有重量輕、柔性結構、可遠距離傳熱、不需要風扇等多項特點,可有效應用於高功率LED燈具,取代傳統龐大且笨重的鰭片散熱結構。
陽傑科技表示,LED照明應用起飛,2008年將發表多款LED室內外燈具。
CTO技術觀-陽傑科技指導教授黃秉鈞克服散熱問題點亮照明路
為什麼一般照明的市場還要等好幾年?LED價格太高、效率不夠、衰減問題、壽命問題都令人質疑,而且LED用作照明的方式正處於新生兒的階段,系統技術更是不成熟;此外,由於沒有人使用過,因此也沒人能夠證明LED照明能像現在既有燈泡或燈管,持續使用好幾年,也增加一個新技術推展到市場的困難度。
LED上游業者認為,路燈會是今年愈來愈熱的領域,中國大陸由於電力缺乏,尤其有廣大的需求,2007年很有機會是LED路燈元年;因此本期「CTO技術觀」專訪現在台灣廠商中,在LED路燈領域腳步較快的陽傑科技指導教授黃秉鈞;台灣已有部分廠商提供原型產品或小量出貨,陽傑也已進入量產階段,陽傑董事長林美東表示,中國大陸有10幾個城市都表達高度興趣,中國大陸可望是市場最早崛起的地區。
黃秉鈞教授擅長的是散熱處理技術,LED系統技術開發上,散熱往往是最難突破的關鍵點,舉個現在當紅的LCD背光源應用為例,廠商多半就是認為LED效率還不夠,致使顆數太多,散熱問題難以突破,導致商品化困難。

事實上,大家對LED質疑的光衰減、壽命問題,就是因為散熱處理不佳所造成的;黃秉鈞引進LHP散熱技術,並以16個月的實際操作,證明因有效散熱,致使衰減問題幾乎沒有發生,因而推估使用可達5萬小時。
使用壽命問題解決,符合市場期待之一,接下來就是最令人關切的價格問題,黃秉鈞對此也精算過,即便一支LED路燈的價格至少要3萬元,相較現行的高壓鈉燈的8,000∼9,000元高得多,然而由LED省電至少3成的後續電費成本估算,使用3年後兩者成本便相等,後續使用LED燈較高壓鈉燈省下更多的電費,使得兩者成本愈拉愈遠。
事實上,前一波油價飆漲,已經提醒世人,因為新興國家的大量需求,能源危機隨時有可能再度引爆,節能和綠色產業已是未來長期明星,投入也是對地球的一大貢獻。基於此立場,也促使投資陽傑的江陵集團董事長林美東對於黃秉鈞教授的節能研發長期支持。
陽傑科技的成立
市場上對陽傑的名字很陌生,公司的規模也不大,除了LED界以外恐怕鮮有人知;它是台大新能源中心育成的第一家公司,2005年由江陵機電獨立出來,LED路燈系統是公司投入開發的第一項產品。
黃秉鈞為何會開發起都沒有人做過的LED路燈呢?他在台大機械系教書30年,散熱和能源是長期的研究領域,1999年時注意到太空技術領域有一項新技術迴路熱管LHP由俄羅斯科學院提出來,但是價格高達15萬美元,他認為該技術一來應該可以商品化應用到各種需要散熱的領域,二來價格實在不需要這麼貴,量產之後應該可以降至10美元,加上他本身和烏克蘭關係就很好,遂進行技術合作移轉。

2003年商品化技術成熟了,應用面成為一個問題,便積極尋找應用領域,包括LED散熱和太陽能傳熱都成為後續研發方向。不過2004∼2005年,以當時的LED上游端技術來說,還未能達到省電的目的,但是在系統開發的研究中,已經可以發現散熱會是技術瓶頸。
直至今日,在LED各項應用的技術開發中,都可以發現散熱始終是業者最頭痛的問題。所以似乎可以簡單來說,LHP技術的確發揮功效,陽傑也找到適合的應用方向。
2005年底,黃秉鈞結合燈具光學、再照明工程光學等不同領域的技術,開發出高亮度LED路燈系統,並且把自家外面路燈換成LED燈,進行實際測試。

與現行路燈相較,LED路燈究竟有沒有足夠的優勢,吸引人進行汰換?以黃秉鈞在2006年底技術最新進展來看,使用的是Cree的晶粒,億光和光寶的高亮度LED封裝,發光效率可以超過72 lm/W。LED燈具全光束,在150W之下亮度可以超過8,000流明;150W為符合國際規範的標準。


如果以鈉燈400瓦的亮度來看,LED燈必須300瓦,也超出標準規範甚多。而且這種鈉燈1年光衰高達6成;相對而言,LED 10年光衰3成,差別甚大。
LED燈的省電功效明顯,依黃秉鈞的最新估算,若是比較射達目標路面的每單位光束耗電量,若同為新品,高壓鈉燈為0.035W/lm,而LED為0.023W/lm,省電35.4%。
若同為壽命期性能的比較,同樣以射達目標路面的每單位光束耗電量來看,高壓鈉燈為0.071W/lm,LED為0.033W/lm,省電更高達53.5%。
很多人會認為一支LED較現行路燈貴太多,但若把眼光放長遠,考量電費支出,長期來看LED較省電。
若以一盞LED路燈3萬元的成本價來看,較高壓鈉燈8,000∼9,000元似乎貴得多,但若考量後續電費支出的差別,大約3年後兩者總體費用相同,這還不計維修費用;因此使用3年以上,LED燈就顯得更為划算。
傳統散熱技術較LHP重5∼10倍
現在一般使用的LED路燈散熱技術,多為導熱板方式,是一片5mm厚的銅板,實際上算是均溫板,把熱源均溫掉;也有加裝散熱片來散熱,但是重量甚重,大約是LHP技術的5∼10倍。
重量在路燈系統上甚為重要,因為路燈高有9米,若太重危險性就增加,尤其遇到颱風、地震都可能產生意外。LHP重0.1公斤,陽傑開發出的系統,100W路燈重6公斤,150W路燈則重8公斤。
使用傳統散熱技術不僅太重,而且因為為銅材質,太硬無法摺;路燈系統必須做外觀設計,影響就很大,則又是另外一個問題。
現在許多廠商對陽傑開發出的散熱方式表示高度興趣,希望能提供散熱模組,不過路燈系統牽涉到燈具造型,千變萬化,沒有辦法以模組來提供;未來進入一般照明領域,造型較為固定時,或許會朝散熱模組來開發。
2008年1月21日 星期一
Photonic Crystal
Greg Parker G and Charlton M are in the Department of Electronics and Computer Science, University of Southampton, Highfield, Southampton SO17 1BJ, UK
We can now buy personal computers that operate at 1 GHz (109 Hz), which is very impressive, but what is the likelihood of a 100 GHz desktop computer appearing on the market? Indeed, given our current understanding of semiconductor technology, even producing a 10 GHz personal computer would seem to be difficult. However, by transmitting signals with light rather than electrons, it might be possible to build a computer that operates at hundreds of terahertz (1012 Hz). Researchers now believe that such an awesome processing engine could be built from optical components made from so-called photonic crystals and quasicrystals. These materials have highly periodic structures that can be designed to control and manipulate the propagation of light.
Basics of photonic band gaps
The easiest way to understand the behaviour of light in a photonic crystal is to compare it to the movement of electrons and holes in a semiconductor. In a silicon crystal, for example, the atoms are arranged in a diamond-lattice structure, and electrons moving through this lattice experience a periodic potential as they interact with the silicon nuclei via the Coulomb force. This interaction results in the formation of allowed and forbidden energy states. For pure and perfect silicon crystals, no electrons will be found in an energy range called the forbidden energy gap or simply the band gap. However, the situation is different for real materials: electrons can have an energy within the band gap if the periodicity of the lattice is broken by a missing silicon atom or by an impurity atom occupying a silicon site, or if the material contains interstitial impurities (additional atoms located at non-lattice sites).
Now consider photons moving through a block of transparent dielectric material that contains a number of tiny air holes arranged in a lattice pattern. The photons will pass through regions of high refractive index - the dielectric - interspersed with regions of low refractive index - the air holes. To a photon, this contrast in refractive index looks just like the periodic potential that an electron experiences travelling through a silicon crystal. Indeed, if there is large contrast in refractive index between the two regions then most of the light will be confined either within the dielectric material or the air holes. This confinement results in the formation of allowed energy regions separated by a forbidden region - the so-called photonic band gap. Since the wavelength of the photons is inversely proportional to their energy, the patterned dielectric material will block light with wavelengths in the photonic band gap, while allowing other wavelengths to pass freely.
It is possible to create energy levels in the photonic band gap by changing the size of a few of the air holes in the material. This is the photonic equivalent to breaking the perfect periodicity of the silicon-crystal lattice. In this case, the diameter of the air holes is a critical parameter, together with the contrast in refractive index throughout the material.
Photonic band gap structures can also be made from a lattice of high-refractive-index material embedded within a medium with a lower refractive index. A naturally occurring example of such a material is opal. However, the contrast in the refractive index in opal is rather small, which results in a rather small band gap.
The potential of photonic-crystal structures was first realized in 1987 by Eli Yablonovitch, then at Bell Communications Research in New Jersey. A few years later in 1991, Yablonovitch and co-workers produced the first photonic crystal by mechanically drilling holes a millimetre in diameter into a block of material with a refractive index of 3.6. The material, which became known as "Yablonovite", prevented microwaves from propagating in any direction - in other words, it exhibited a 3-D photonic band gap. Other structures that have band gaps at microwave and radio frequencies are currently being used to make antennae that direct radiation away from the heads of mobile-phone users.
In spite of this success, it has taken over a decade to fabricate photonic crystals that work in the near-infrared (780-3000 nm) and visible (450-750 nm) regions of the spectrum. The main challenge has been to find suitable materials and processing techniques to fabricate structures that are about a thousandth the size of microwave crystals.
A rough estimate of the spacing between the air holes (or the lattice size) is given by the wavelength of the light divided by the refractive index of the dielectric material. The problem in making small structures is compounded because it is more favourable for a photonic band gap to form in dielectrics with a high refractive index, which reduces the size of the lattice spacing even further. For example, suppose we wanted to create a photonic crystal that could trap near-infrared light with a wavelength of 1 µm in a material with a refractive index of 3.0. We would have to create a structure in which the air holes were separated by about 0.3 µm - an extremely difficult task. If the scale was 1000 times smaller, we could build the structure atom-by-atom using a chemical reaction; and if it was 1000 times larger we could build the structure mechanically, as Yablonovitch and co-workers did.
To be able to create photonic crystals for optical devices, we need to use state-of-the-art semiconductor-microfabrication techniques with their associated high production costs and investment. For this reason computer modelling of prospective photonic-crystal structures is also a very important area of research, as it may prevent expensive fabrication errors later.
Optical communications
So why are photonic crystals generating so much interest? Again it is useful to draw analogies with silicon. The current explosion in information technology has been derived from our ability to control the flow of electrons in a semiconductor in the most intricate ways. Photonic crystals promise to give us similar control over photons - with even greater flexibility because we have far more control over the properties of photonic crystals than we do over the electronic properties of semiconductors. Given the impact that semiconductor materials have had on every sector of society, photonic crystals could play an even greater role in the 21st century, particularly in the optical-communications industry.
In current communications systems, audio or video signals are encoded as streams of digital data packets. These voltage pulses are applied to a light-emitting diode (LED) or a semiconductor laser, which converts them into short pulses of light that are then sent along an optical-fibre network. Many different conversations or video signals can be transmitted using a single wavelength of light by interweaving the data packets from different sources, a technique known as time-division multiplexing. The optical data pulses are sorted at the receiving end of the fibre, where they are converted by photodetectors into continuous analogue electrical signals that are then transmitted along copper wires.
A simple way of increasing the amount of data that can be transmitted by a single optical fibre is to make the incoming electronic pulses as short as possible. Current optical systems have achieved data rates in excess of 40 gigabits per second. But to increase this value significantly will require cheap, bright LEDs that can be switched on and off at very high speed.
Another way to increase the capacity of the fibre is to add new signals at other optical wavelengths, a method known as dense wavelength division multiplexing (DWDM). However, the optical fibre is only transparent over a small range of wavelengths, so the number of separate conversations that can be transmitted depends on the linewidth of neighbouring optical channels (which is currently at the sub-nanometre level). Encoding and sorting thousands of such channels poses quite a problem: at the transmitting end of the system, each wavelength channel requires a very stable light source that only emits in a very narrow range of wavelengths. Although LEDs offer high switching speeds, they emit light over a wide range of wavelengths, which makes them less suitable than lasers for DWDM systems.
At the receiving end, very narrow linewidth filters and optical switches are required to separate individual channels and then route them to the appropriate destinations. Due to the large number of individual components in a DWDM system, it makes sense to combine as many of them as possible onto an "integrated" optical chip. This would reduce both the amount of costly manual work that is needed to build the system and the number of possible points where it could fail.
Such integration, however, raises other problems. First we need to develop small-scale optical "interconnects" - tiny planar waveguides that can steer light round tight corners. While it is straightforward to route electrons round sharp bends in microchips, it is impossible to direct light in the same way using conventional glass waveguides because the losses at the bends are so large.
Photonic crystals could address many of the problems that currently limit the speed and capacity of optical-communications networks. For example, these structures could be used to create novel LEDs and lasers that emit light in a very narrow wavelength range, together with highly selective optical filters that could be integrated on a chip.
Light-emitting diodes play a key role in optical-communication systems. These devices are made from so-called photoemissive materials that emit photons once they have been excited electrically or optically. These photons are typically emitted in many different directions and also have a range of wavelengths, which is not ideal for communications applications. We can create an LED that only emits light in the forward direction by placing a reflector behind the photoemissive layer. However, the efficiency of such a device is limited by the efficiency of the reflector.
Photonic crystals could be used to design a mirror that reflects a selected wavelength of light from any angle with high efficiency. Moreover, they could be integrated within the photoemissive layer to create an LED that emits light at a specific wavelength and direction.
A far simpler method of producing 3-D band gaps at very short wavelengths has been pursued by Judith Wijnhoven and Willem Vos at the University of Amsterdam. The technique relies on the self-arrangement of sub-micron-sized silica spheres in a colloidal suspension. However, the rather low refractive index of the silica relative to air means that the refractive-index variation across the lattice is not high enough to create a truly 3-D photonic band gap. The team has overcome this limitation by filling the air voids between the spheres with a titania-dioxide solution, which has a high refractive index. The solution undergoes a chemical reaction that causes solid titania to form. This process is repeated several times and the silica spheres are finally dissolved to leave a close-packed lattice of spherical air voids in a titania matrix (figure 1b).
Meanwhile, John Holtz and Sanford Asher of the University of Pittsburgh in the US have fabricated "tunable" photonic crystals from a suspension of polymer spheres in a hydrogel film, a synthetic polymer that absorbs water. In this case, the wavelength of the band gap can be adjusted by shrinking or expanding the hydrogel. However, although colloidal structures are easy to make and overcome the problem of scale in a very clever way, it is not easy to incorporate them within the active heterostructure of an LED.
Fortunately 2-D periodic lattices exhibit some of the useful properties of a truly 3-D photonic crystal, and are far simpler to make. These structures can block certain wavelengths of light at any angle in the plane of the device, and can even prevent light entering from certain angles in the third dimension (i.e. perpendicular to the surface). Thus 2-D photonic crystals are a good compromise for many applications and are easily incorporated within planar waveguides.
Microcavities in photonic crystals
Photonic crystals built from photoemissive materials, such as III-V semiconductors and glasses doped with rare-earth atoms, can also be used to make narrow-linewidth lasers that could potentially be integrated with other components in an optical-communications system. The lasers are made by introducing a small number of holes that are slightly smaller or larger than the other holes in the photonic-crystal lattice. These "microcavities" generate a narrow so-called defect mode within the photonic band gap.
While the material emits light in a wide spectral range, only the wavelength that matches the wavelength of the defect mode is amplified because it can propagate freely through the material. The laser cavity is formed either by the crystal facets or by external mirrors that surround the glass. The intensity of the propagating light increases as it undergoes successive reflections and travels back and forth through the photonic crystal. Meanwhile, light at other wavelengths is trapped within the photonic crystal and cannot build up. This means that the laser light is emitted in a narrow wavelength range that is directly related to the diameter of the microcavity divided by the diameter of the regular holes. Moreover, the linewidth can be reduced further by using unusual geometries of the photonic-crystal lattice.
Such microcavities are also much more efficient at trapping light than the cavities formed in semiconductor diode lasers since there are fewer directions in which the photons can escape from the cavity.
The rate of photoemission in an active medium can be greatly increased by maintaining a high optical flux density. Since microcavities act as light traps, they provide a good method of enhancing the rate of photoemission in LEDs, and are crucial for the operation of lasers. Moreover, the increased rate of photoemission means that microcavity LEDs and photonic-crystal lasers can be switched on and off at far greater speeds compared with conventional devices, which could lead to higher data-transmission rates and greater energy efficiency. Indeed, such devices are the subject of intense effort within the field of optoelectronics.
Preliminary experiments have been performed at microwave frequencies on defect structures within photonic crystals made from "passive" materials that do not emit light. Recently John Joannopoulos and colleagues at the Massachusetts Institute of Technology (MIT) in the US have demonstrated very strong photon confinement within a simple 1-D microcavity made by etching a single row of holes onto a narrow silicon waveguide.
Photonic-crystal microcavities that are fabricated from passive materials, such as silicon dioxide and silicon nitride, could also be used to create filters that only transmit a very narrow range of wavelengths. Such filters could be used to select a wavelength channel in a DWDM communications system. Indeed, arrays of these devices could be integrated onto a chip to form the basis of a channel demultiplexer that separates and sorts light pulses of different wavelengths.
Although complex photonic-crystal LED and laser structures are being developed, fundamental questions about the formation, operation and efficiency of photonic band gaps remain unanswered. Real photonic-crystal waveguides are far from ideal because they suffer losses due to diffraction and scattering, and due to an optical mismatch at the surface joining the device to input and output waveguides. These loss mechanisms need to be fully understood and the devices need to be optimized for particular wavelengths before they can become commercially viable.
Passive materials provide a good testing ground to investigate these factors. Our group at Southampton University is studying the physics underlying band-gap formation, verifying computational-design methods experimentally, and developing integrated optical filter and switching devices.
(a) This photonic waveguide formed from a thin silicon-nitride membrane contains a triangular lattice of air holes separated by 300 nm. The air gap below the waveguide leads to stronger photon confinement. (b) A plot of transmission versus wavelength for the device shows that it has a photonic band gap between 725 nm and 825 nm if the electric field associated with the electromagnetic wave is perpendicular to the direction in which the light wave propagates (red). In contrast, the light can pass freely through the material when the magnetic field is perpendicular to the direction of travel (blue). In this case, the photonic band gap is said to be incomplete. (c) A photonic crystal made from a piece of silicon approximately 1 x 1.5 cm viewed from above. Laser radiation with a wavelength that lies inside the band-gap range enters the structure from the left and is completely blocked. (d) Light at longer wavelengths outside the band gap can pass through the structure.
For example, we have built a photonic-crystal device that works as a simple filter (figure 2). The device was created by growing a thick layer of silicon dioxide on the surface of a silicon substrate, followed by a layer of silicon nitride. The positions of the holes were defined by patterning the top surface of the waveguide with electron-beam lithography. The underlying silicon dioxide was then etched away to create a free-standing porous silicon-nitride membrane that blocks light over the wavelength range 725-825 nm. Similar devices were also fabricated with band gaps at shorter visible wavelength. Although it is more challenging to fabricate photonic crystals at optical wavelengths, it is easier to conduct experiments with them due to an abundance of visible-light sources and detectors.
Quasicrystals overcome losses
Real photonic crystals experience losses due to the mechanisms described earlier. Such losses are not a problem for active laser devices in which a large amount of optical radiation is generated and then coupled directly to an optical fibre pressed against it. In contrast, passive devices are typically used to filter a weak optical signal that may have travelled through hundreds of kilometres of optical fibre - in this case it is crucial to keep any further losses to a minimum.
As well as the fundamental problem of transferring the light from a waveguide into a photonic-crystal filter, unwanted back reflections from the filter must also be minimized as they reduce the size of the signal pulse and may lead to errors in the high-speed optical links.
One way to reduce reflections would be to reduce the refractive index of the materials from which the photonic crystal is fabricated. However, this creates something of a paradox since the formation of the photonic band gap is largely governed by the contrast in refractive index between the materials.
Nevertheless, since photonic crystals are artificial structures, we are at liberty to change the geometric parameters to compensate for the reduction in refractive index. The band gap can be restored in materials with a low refractive index by increasing the number of degrees of symmetry in the lattice.
For example, a rectangular arrangement of air holes etched into a silicon block has twofold symmetry. In other words, photons travelling along the length of the photonic crystal experience a different hole spacing from photons travelling at right angles within the plane of the material. This means that the photonic band gap changes depending on the direction in which the light travels, and it may disappear altogether in some cases. However, if a triangular lattice arrangement - which has sixfold symmetry - were used instead, light from any direction in the plane of the material would experience the same photonic band gap.
Interconnects for optical circuits
Miniature waveguides that could be used to transmit light signals between different devices are a key component for integrated optical circuits. However, the development of such small-scale optical interconnects has so far been inhibited by the problem of guiding light efficiently round very tight bends.
Conventional optical fibres and waveguides work by the process of total internal reflection. The contrast in refractive index between the glass core of the fibre and the surrounding cladding material determines the maximum radius through which light can be bent without any losses. For conventional glass waveguides this bend radius is about a few millimetres. However, the interconnects between the components on a dense integrated optical circuit require bend radii of 10 µm or less.
It is possible to form a narrow-channel waveguide within a photonic crystal by removing a row of holes from an otherwise regular pattern. Light will be confined within the line of defects for wavelengths that lie within the band gap of the surrounding photonic crystal. Since a porous material has no available modes at this wavelength, an optical quantum well forms in the waveguide region and traps the light. Under these conditions we can introduce a pattern of sharp bends that will either cause the light to be reflected backwards or directed round the bend. Joannopoulos and colleagues at MIT have shown theoretically that the light will be guided round the bend suffering little, or even zero, loss due to back reflectance.
We have recently tested these ideas experimentally on a photonic-crystal beam splitter that we designed and built at Southampton (figure 4). We defined a wide Y-shaped "defect waveguide" within the photonic crystal by removing some of the holes from the lattice. This device showed that a small amount of light was in fact guided round the bend, although the losses were quite high. However, the photonic crystal was found to modify the spectral properties of the transmitted light in a beneficial way. For example, the amount of light reflected back from the pointed corners was reduced. We are currently investigating methods to optimize these structures.
Materials with photonic band gaps could speed up the Internet by improving the transmission of long-distance optical signals. One drawback with conventional optical fibres is that different wavelengths of light can travel through the material at different speeds. Over long distances, time delays can occur between signals that are encoded at different wavelengths. This phenomena - known as dispersion - is worse if the core is very large, as the light can follow different paths or "modes" through the fibre. A pulse of light travelling through such a fibre broadens out, thereby limiting the amount of data that can be sent.
These problems could be solved by an extremely unusual "holey fibre" developed by Philip Russell and Jonathan Knight of the University of Bath and co-workers. The fibre has a regular lattice of air cores running along its length and transmits a wide range of wavelengths without suffering from dispersion. It is made by packing a series of hollow glass capillary tubes around a solid glass core that runs through the centre. This structure is then heated and stretched to create a long fibre that is only a few microns in diameter. The fibre has the unusual property that it transmits a single mode of light, even if the diameter of the core is very large.

Future outlook
Predictions are always difficult to make - however, the future for photonic-crystal circuits and devices looks certain. Within five years a number of basic applications will start making an appearance in the market-place. Among these will be highly efficient photonic-crystal lasers and extremely bright LEDs. On the same timescale we hope to have demonstrated the feasibility of using photonic-crystal waveguides to route light round micron-sized optical benches, and the use of photonic crystals for high-resolution spectral filtering. These demonstrators may be combined to produce a commercially viable "spectrometer on a chip" within a ten-year timescale. Meanwhile, circuits of a similar complexity - including "add-drop filters" and Mach-Zehnder interferometers, common components in optics - will be available at about the same time.
By the time every home is connected to an optical-fibre network, "set-top boxes" that sort and decode the signals will contain photonic-crystal circuits and devices rather than cumbersome optical fibres and silicon circuits. And on a five- to ten-year timescale we should have demonstrated the first photonic- crystal "diodes" and "transistors". A demonstration of the first photonic- crystal logic circuit could even take place in the next 10 to 15 years, while a prototype optical computer driven by photonic crystals could be available within the next 25 years. Surprisingly, synthetic opals could even find a niche in the valuable jewellery and artwork markets, while thin photonic-crystal films could also be used as anti-counterfeit devices on credit cards.
If our predictions are hopelessly awry, by then we hope that most people will have forgotten we made them. Nevertheless the future for photonic crystals looks bright.
Further reading
M D B Charlton, S W Roberts and G J Parker 1997 Guided mode analysis and fabrication of a 2-dimensional visible photonic band structure confined within a planar semiconductor waveguide Mater. Sci. Engin. B49 155
J D Joannopoulos, R D Meade and J N Winn 1995 Photonic Crystals: Molding the Flow of Light (Princeton University Press)
M Senechal 1995 Quasicrystals and Geometry (Cambridge University Press)
P R Villeneuve and M Piché 1994 Photonic bandgaps in periodic dielectric structures Prog. Quantum Electron. 18 no12 p153
E Yablonovitch 1987 Inhibited spontaneous emission in solid-state physics and electronics Phys. Rev. Lett. 58 2059
E Yablonovitch and T J Gmitter 1989 Photonic band structure: the face- centered-cubic case Phys. Rev. Lett. 63 1950
M E Zoorob et al. 2000 Complete photonic bandgaps in 12-fold symmetric quasicrystals Nature 404 740
Comprehensive database of photonic-crystal publications and Web resources www.neci.nj.nec.com/homepages/vlasov/photonic.html
2008年1月16日 星期三
火線話題-嘉晶磊晶薄膜太陽能電池案省思,太陽能不能只是夢 而必須落實產出
近期在市場炒得沸騰的嘉晶磊晶薄膜太陽能電池進度,在嘉晶公告因轉換效率僅達12%,量產仍不符合成本競爭後,揭開嘉晶發展太陽能事業的實際進程。向來低調的嘉晶因為早期被歸類為太陽能類股,造成太陽能產品未上市股價先轟動,而如今其薄膜太陽能電池發展進度不如預期,也代表不論結晶矽或新世代的太陽能產品,都隱含著技術突破時間表難以確定的風險。嘉晶磊晶薄膜太陽能電池在2008年1月10日向經濟部工業局報告成果前,各個平面媒體就已持續關注這個案子的進度,主要是在公布之前市場就傳出人員異動的風聲,且2007年嘉晶本業半導體磊晶呈現衰退的走勢,再加上營收中仍無太陽能產品的任何貢獻,加上外界對其太陽能產品的量產時間表又難以探知,適逢其磊晶薄膜太陽能的專案已接近到期,進而吸引各媒體競相挖掘真相。
嘉晶的磊晶矽薄膜太陽能電池產品應該屬於改良型傳統結晶矽太陽能電池,因為它以純度較低的矽基板做為長晶的基礎,以磊晶薄膜的技術生產,一旦它的產品開發成功,不但可以解決現今多晶矽料源缺乏問題,還可以因為採用較低純度的矽基板而大幅降低成本,而且包括市面上積極在推廣的冶金級矽等都有了用武之地。所以,該產品有它的爆發力,只不過要成功做出轉換效率與一般太陽能電池般可以競爭的水準,想來也不是1、2年可以做得到的事,畢竟目前全球似乎仍未耳聞有成功案例,而市場的期待與嘉晶實際的運作似乎仍有一段落差,導致自1月10日公布以來,股價一路不振。想想目前到底有多少業者宣稱將投入太陽能行列,不論是要將傳統結晶矽做到世界級的高轉換效率,或者是投入各類薄膜或非傳統型的太陽能電池期望要做到產品商品化的境界,目前來看,這些產品目前都還沒有兌現,而且市場必須花相當的等待年限才可能看到產品商業化,到底這些夢何時該落實,想來許多投資人或投入者心中都該擺放一個時間表。而在這些新產品等待商品化或成功量產的期間裏,沒人可以保證,投入生產的廠商中,不會有摻雜「純綷做夢」者,尤其是跟其它國外投入同業的業者來說,不論是耕耘時間、投入技術的時間、甚至是資本的比例、現有產品的品質特性表現等,都難以相比,市場要知道的是除了口頭的宣言外,業者到底實際投入了多少?到底是怎麼規劃這個產業?其實許多市場分析師私底下透露,投資市場近期似乎有醒悟的味道,尤其是2008年即將要準備投入量產的非晶矽薄膜太陽能電池,從相關類股來看,其實在幾波大盤向下調整後,也漸回到其未宣布投入薄膜太陽能前的股價水位,分析師認為,這主要的原因來自於非晶矽薄膜太陽能電池和結晶矽太陽能不同,兌現的等待時間較長,回收時間較慢,不確定的風險相對也較高,可以看到表現的結晶矽類股都受大盤影響向下調整了,這些需更長期才實現的夢自然得做更徹底的調整。太陽能給的夢很美,尤其是2004年~2005年間讓茂迪、益通、大陸尚德及其它知名的國際大廠等一夕成名,進而成為各界競相投入的領域,又因為受限於多晶矽缺料的影響,所以投入薄膜、投入砷化鎵等等。只不過,不論是專業投資人或業餘投資人現在更能體會,探究經營者的葫蘆裏到底是賣什麼藥?到底何時可以落實夢想,更是重要。
2008年1月15日 星期二
LED車燈商機潛力大 成本、散熱問題待克服
Simon說這個市場不能碰--本人不以為然,大家覺得如何?
我們的主動散熱技術絕對有實力能解決這個問題!
---------------------------
Strategy Analytics發表最新市場研究報告指出,LED在車用LCD背光及外部照明領域的應用將逐漸擴大。包括日亞(Nichia)、歐司朗(Osram)、Lumileds在內的主要LED供應商,目前都正在與汽車夥伴合作,以搶攻市場大餅;預期到2014年該部份市場價值為10億美元。
Strategy Analytics表示,汽車內部的LED應用將繼續是車用LED大量需求的來源;而隨著限制LED在車頭燈上使用的技術壁壘正逐漸被突破,未來將會有更多的LED適用於汽車的遠、近光燈。
Strategy Analytics表示,這樣的趨勢在早期將受成本限制,估計LED應用於汽車外部照明,還需要兩年時間才有辦法超越傳統照明市場。目前與LED元件製造直接相關的成本問題及散熱組件、電子控制等額外應用成本問題仍存在,這將阻礙高亮度LED在低利潤量產汽車部份的發展。
江蘇:能源瓶頸是這樣被打開的
讓我們來看看目前大陸的能源政策,就知道未來該往哪裡尋找機會!
----------------------------------------------------
新華網南京1月15日電(記者 鄧華寧)
傳統工業大省江蘇在邁入重化工階段後,工業能耗已佔全省能耗總量的80%,高于全國平均值10個百分點,遠高于廣東、浙江、上海等沿海省市。
江蘇通過工業節能、科技造能兩種手段,大力推進節能減排,2006年、2007年連續兩年單位能耗下降4.02%,為“十一五”實現單位能耗下降20%的約束性指標打下堅實基礎。
摸清能耗家底 找準節能突破口
“經濟結構和產業基礎決定了江蘇節能降耗的難度很大。”江蘇省宏觀經濟研究院院長顧衛東表示。2005年,江蘇省每萬元GDP的能耗為0.92噸標準煤,比全國1.22噸標準煤的平均水平低25%,能源利用的效率已經在全國領先。江蘇節能空間相對較小,完成約束性指標的壓力較大。
根據國家分解的指標,江蘇省“十一五”期間主要污染物化學需氧量(COD)和二氧化硫需要分別削減15.1%和18%,遠高于全國削減10%的平均水平。
怎樣使經濟發展從“又快又好”轉變為“又好又快”,確保完成“十一五”節能降耗的硬指標?工業節能是關鍵。江蘇省經貿委能源處負責人介紹,工業能源消費量約佔江蘇省能源消耗總量的80%,這一比重決定工業單位增加值能耗的高低對單位GDP能耗高低起著關鍵作用。
從工業行業消費結構看,江蘇主要能耗來自兩大部分,即制造業和電力、燃氣及水的生產供應業。其中,制造業能耗佔工業總能耗的近70%;電力、燃氣及水的生產供應業佔工業總能耗的近30%。在理清能源消費結構的基礎上可以看出,這兩大行業應當成為江蘇省工業節能的重中之重。
把好能耗源頭關 勾勒循環利用鏈
江蘇省經貿委主任韓慶華介紹,認清能源消耗結構後,江蘇把節能作為解決能源問題的根本出路,嚴把能耗增長源頭關。
2006年,江蘇啟動全省性節能降耗工程。全省對冶金、建材、化工、電力、紡織等5個重點行業實施能耗總量控制,對年耗能5000噸標煤以上的重點企業,運用各種新技術,係統組織實施節能降耗工程。 2007年上半年,全省有近30條新型幹法水泥窯實施純低溫余熱發電改造,水泥行業能耗降低率比全省平均水平高出1.9個百分點。
江蘇省還對高耗能行業制訂強制性的能耗限額標準,建立和完善主要用能設備能效標準,抑制高耗能、高污染行業的盲目發展。建立了固定資產投資項目節能審查制度。2007年城鎮固定資產投資中,黑色金屬冶煉及壓延加工業、紡織業,造紙及紙制品業、化學原料及化學制品制造業投資增幅均大幅回落。
微觀層面上,重點耗能企業挑起節能大梁。全省41515家規模以上企業中,被列入國家1000家耗能監測名單的有67家企業,雖然僅佔全省規模以上企業單位數的0.2%,但其綜合能耗卻佔到規模以上工業能耗的35.4%。通過不斷強化管理和改造,目前這67家企業綜合能耗的增長速度已經低于工業總產值增長速度14.5個百分點。
“工業廢水、廢氣、廢料不是垃圾,而是沒有被利用的資源。”沙鋼集團副總裁龔盛告訴記者。2007年,沙鋼集團已經實現轉爐“負能”煉鋼,企業“三廢”全部回收利用,還通過短流程實現熱能綜合利用。成為我國鋼鐵行業第二家實現全幹熄的企業,僅此項每年可回收能源6.5萬噸標準煤。2007年沙鋼依靠循環經濟節省20億元。
如今,在江蘇星羅棋布的工業園區,企業內部以及企業之間,通過技術創新,多渠道、全方位探索節能、環保和資源綜合利用新途徑,把節能、環保和資源綜合利用有機地結合起來,一條條能源循環利用的鏈條被勾勒出來。
淘汰落後產能 鍛造清潔能源鏈
2007年太湖藍藻事件後,江蘇以此為產業結構調整的契機,大力淘汰落後產能。全年共關閉“小化工”1934家,其中太湖流域關閉1197家,淘汰小火電機組184萬千瓦、落後煉鋼煉鐵能力241萬噸、小水泥300萬噸。據不完全統計,2007年已淘汰高損耗變壓器、空氣壓縮機、鍋爐、電機等落後用能設備6300多臺(套),其中電力係統淘汰S7型及以下變壓器5000臺,居全國前列。
在淘汰落後的同時,江蘇還大力開發清潔能源。江蘇省不久前決定,“十一五”期間將投資1500億元大力發展清潔能源產業,重點包括太陽能利用、半導體照明、新型動力型電池、節能、綠色能源等領域重大關鍵技術的開發以及產業化。
江蘇省經貿委電力處處長李強說,到“十一五”期末,江蘇省能源需求總量將增加到2.2億噸左右,電力需求約增長70%,能源將成為社會經濟發展的瓶頸。在電力建設中,目前新能源的投資只佔5%左右,未來3年內將增至10%以上。
目前,在太陽能光伏產業鏈方面,江蘇有無錫尚德、南京中電光伏等一批上規模、高水平的骨幹企業,擁有60多項自主知識產權和20多項發明專利。太陽能硅片產能佔全國70%。風能產業方面,江蘇省規劃“十一五”期間建設風電項目100萬千瓦,現在在建和已確定的項目有如東一期10萬千瓦、二期10萬千瓦、東臺一期20萬千瓦、大豐風電20萬千瓦等。目前,從風機、葉片到齒輪箱等風電設備的零部件,在江蘇已大部分完成了國產化。生物質能產業化正在江蘇各地蓬勃開展。江蘇第一座焚燒垃圾的發電廠,已于2005年10月正式並網發電,計劃和在建的垃圾焚燒發電廠還有無錫、蘇州等地的10座。全省目前已建成並投入運行的秸稈氣化工程約61處,年利用秸稈1萬多噸。
“過去以化工為主的南京市,目前已形成較完整的風電產業鏈條。未來15年,國家要將風電比重從現在不足1%,提高到15%以上。江蘇正在開展‘海上三峽’計劃,要在沿海建設3000萬千瓦裝機總量的風電電廠。江蘇正在把風能、太陽能等取之不盡、用之不竭的能源變成開發的主打產品。”南京汽輪公司總經理沈群告訴記者。
美研發出高效光電轉換納米材料
本報華盛頓1月13日電 美國加州大學聖克魯玆分校張勁(音譯)教授領導的包括中國、美國和墨西哥三國研究人員之內的研究小組日前在《物理化學雜志》網站上發表文章表示,他們成功研制出一種能高效率將太陽能轉換成電能的納米薄膜材料。該成果不僅能極大地提高太陽能電池光電轉化率,而且可以用于其他能源技術中。
為開發高效且廉價的太陽能電池,近來利用納米結構的新材料成為重點研發方向。人們發現,兩種制造太陽能電池材料的納米技術方法顯示出了獨特的前景。一是將其他元素(如氮)摻雜于金屬氧化納米顆粒(例如二氧化鈦)形成的薄膜中;二是用能強吸收可見光的量子點(納米尺寸的晶體)向金屬氧化薄膜注入電子。摻雜和量子點利用的目的都是增強金屬氧化材料對可見光的吸收能力。
張勁領導研究小組將上述兩種方法結合起來,獲得的太陽能電池材料的性能比單獨使用任何一種方法產生的都要好。在測試中,新的納米復合材料的性能大于兩種單獨成分之和。他表示:“我們起初以為能實現的最好結果是達到兩者之和。而且假如出現偏差,我們可能得到更糟糕的結果。但是令人吃驚的是,這些材料更為理想。”
研究中,張勁他們借助高技術儀器來了解新的納米復合材料的特性,其中有原子力顯微鏡(AFM)、透射電子顯微鏡(TEM)、拉曼光譜儀和光電化學技術。他們制作的二氧化鈦金屬膜的厚度在150納米至1100納米之間,二氧化鈦粒子的平均尺寸是100納米。他們將二氧化鈦晶格材料摻雜了氮原子,同時用化學方式將硒化鎘制成的量子點連接在其上,用于敏化。
新的復合材料體現出了兩種技術聯合的優勢。氮摻雜讓新材料吸收廣泛的光能,包括電磁波譜中的可見光波段;量子點則增強可見光吸收,并增加光電轉換。與僅摻雜了氮或者僅嵌入了硒化鎘量子點的材料相比,新的納米復合材料表現出了更高的“光電轉化率(IPCE)”。張勁表示,這種納米復合材料的IPCE是其他兩種材料的IPCE之和的3倍。其原因是電荷更易于在同時擁有量子點敏化和氮摻雜的納米材料內跳躍。
新的納米復合材料不僅可以用于改進太陽能電池,而且還可以作為其他能源技術的組成部分。張勁他們的長期目標之一就是讓高效的太陽能電池與最先進的光電化學電池相結合,這樣的裝置在理論上可能利用陽光產生的能量分解水生產氫燃料。此外,新的納米復合材料還可能有■力用于把二氧化碳轉化為碳氫燃料(例如甲烷)的裝置。
2008年1月11日 星期五
茂迪(6244)鄭福田請辭董事長暨總經理 左元淮繼任
1.董事會決議日期:97/01/10
2.舊任者姓名及簡歷:鄭福田先生
3.新任者姓名及簡歷:左元淮先生
4.異動原因:鄭福田先生因為個人健康因素請辭,經董事會推舉由左元淮先生繼任為茂迪公司董事長及總經理
5.新任生效日期:97/01/10
6.其他應敘明事項:
鄭先生福田於1981年加入茂迪並擔任茂迪董事長,任職期間讓茂迪轉型成為國內太陽能電池的龍頭廠商,並帶領茂迪上櫃掛牌成功,董事會對於鄭董事長貢獻深表感激,並希望其身體早日康復
左元淮先生為紐約市耶西華大學物理博士,曾任美國能源部再生能源研究室資深科學家超過18年的時間,其間專研太陽能產業相關技術,是全世界太陽能產業的佼佼者,於1999年7月經鄭福田董事長力邀加入茂迪,加入茂迪短短八年,做出令人刮目相看的成績,使茂迪光電事業部由2000年的1億營收、5MW的產能及2MW的產出,到2007年成長達到153億營收、240MW的產能及176MW的產出,相信以左元淮董事長過去令人驚艷的經營績效,必能帶領茂迪邁向更輝煌的未來。
由於茂迪原料將自2009年起因新供應商加入而趨於寬裕,配合上游整合策略的逐步實現,茂迪將於今年在台灣及大陸昆山進行規模太陽能電池產能的擴充計畫,預計2008年底年化產能可達580MW,產出目標達280MW,為茂迪未來的高成長打下堅實的基礎。
2008年1月10日 星期四
太空太陽能發電有望成為未來能源之星
當世界各國都在為煤炭、原油和全球變暖焦頭爛額時,聯合國氣候大會中規模最小的一次會議正在展望解決能源問題的可能途徑。會議上,各國專家提出了許多奇思異想,例如種植海藻來吸收二氧化碳等。
其中,有一個想法格外引人注目,是因為它竟贏得了美國五角大樓這樣一位重量級的支援者。
2007年10月,美國五角大樓國家安全太空辦公室(NSSO)悄然推出一份研究報告,建議美國政府在未來10年投入100億美元建造一顆能將10兆瓦太陽能傳回地球的試驗衛星,併為下一步的私人參與開發此技術提供經濟激勵。這就是被稱為太空太陽能發電站的研究項目。從20世紀70年代起,人們就寄望它能為人類提供“價格合理、清潔、安全、可靠、可持續和可擴展的能源”。
止步于高昂成本的夢想
太空太陽能發電站的想法最初在1968年由美國麻省裏特諮詢公司的工程師彼特·格拉斯提出。格拉斯設想了一個面積達50平方公里的太陽能電池板陣列,其中每塊電池板都能產生數千瓦的能量。人們用火箭將這些電池板送入地球同步軌道,並讓數百名宇航員在太空中完成組裝工作。在他的設計方案中,太空發電站的電池板能不斷調整角度以面對太陽,然後借助一個長達1公里的微波天線將太陽能傳回地球。為實現這一目標,這個巨大的天線必須安裝在萬向裝置上,使它能自由旋轉而不受陣列中其他設備的影響。地面接收天線則更為壯觀,佔地超過100平方公里。如果這個夢想得以實現,它將成為最偉大的太空奇跡,國際空間站在它面前就不過是摩天大樓前的一間玩具房子。
由於大氣層外沒有大氣吸收、晝夜交替和雲層遮擋,因此相同時間內,太空發電站的發電量將是在地球上相同面積太陽能電站產能的20倍。這就意味著在距地球3.6萬公里的同步軌道上,每平方公里面朝太陽的衛星都能不間斷地接收到1360瓦的太陽能,即使當地球被雲層遮擋時也是如此。
日本宇宙航空研究開發機構(JAXA)高級任務研究中心主任森政弘說,即便將建設期間所需能量考慮進去,太空發電站產生的能量也比地面上佔地面積相同的太陽能發電站高5倍。
雖然太空發電站的大規模建設有望一舉解決溫室氣體排放和能源短缺問題,但美國在20世紀70年代進行了初步研究後還是放棄了這種想法,因為其建設成本高得驚人。即使在今天,僅將一顆這樣的太陽能衛星送進太空就需要1萬億美元,而在太空建發電站至少需要十幾顆這樣的衛星。高昂的成本,讓人類不得不止步。
助推夢想的技術突破
雖然在太空建設發電站的計劃暫時擱置,但人類探索太空太陽能的腳步卻從未止步。美國太空太陽能專家約翰·曼金斯說,近年來太陽能領域的三大技術突破可使太陽能衛星的大小和成本降到可接受的水準。曼金斯之前曾是美國宇航局的一位研究管理人員,現在他的可控能源技術公司(ManagedEnergyTech鄄nologies)則是太空太陽能領域研發的領頭羊。他解釋說,與20世紀70年代相比,如今的太陽能電池的效率提高了4倍,因此所需的電池板的面積可大大縮小。其次,微波傳送技術也大大提高,利用固定裝置就能使微波光束實現精確指向,而不再需要旋轉天線。因此可以用體積小、組裝簡便的模組天線替代原來1公里長的天線。最後,機器人可以替代宇航員在太空中完成組裝工作。
在日本,太空發電站的研究更加如火如荼。20世紀80年代日本的多所大學就展開了相關研究。而日本宇宙航空研究開發機構與日本經產省共同資助1200萬美元的太空太陽能十年計劃也即將結束第一階段的研究。
作為宇宙航空研究開發機構的一員,森政弘的目標是建設一個發電量為10億千瓦的太空發電站,並且要將建設成本控制在10億美元以下,每度電的成本也不高於8美分。與一般煤電每度5美分、核電每度10美分的成本相比,這個價格也算得上經濟實惠。為此,他設計了兩面巨大的鏡子,將太陽光聚集到兩個直徑為1.25公里的太陽能電池上,然後通過微波傳輸器將能量傳輸到地球。
日本神戶大學和無人太空實驗自由飛行物研究所(USEF)的研究小組則從減少衛星重量方面進行研究。他們設計的太陽能電池板只有100平方米大,並且固定在控制衛星上。雖然它不能調整角度面對太陽,但簡單的裝置使重量大大減輕,發射成本也隨之下降。研究人員說,按照這一設計,發電站在建設初期就可以開始對地面供電,而模組化的特點也使日後對它進行擴展非常容易。
美國國家安全太空辦公室(NSSO)則對太空太陽能的軍事用途感興趣。太空發電站傳輸回地球的微波束較為集中,因此如果給戰場上的士兵配發接收天線,他們就能隨時用微波對設備充電。另外,太空太陽能也能為邊遠地區的軍事基地提供便利。而在這些地區,傳統供電方式每度電的成本在1美元以上。
除適用性和實用性外,發電站的安全性恐怕是人們最關心的問題。日本麻布大學的帕特裏克·柯林斯卻認為這種擔憂毫無必要,因為一束低能微波的能量,還不如從微波爐中洩露出來的能量大。為確保安全,他建議在地面設置一個禁飛區和地面人員禁入區,用於接收從巨型衛星上傳回的微波光束。
成本、性能、安全問題都已大大改善,太空發電站大展身手的時刻是否已經到了呢?
令人期待的明日之星
隨著全球變暖和能源短缺問題日益緊迫,向太空要能源這一想法愈發顯得令人期待。日本無人太空實驗自由飛行物研究所近期的一項研究顯示,太空發電站每度電的二氧化碳排放量僅與核電相當。美國國家航太學會副會長馬克·霍普金斯也說,太空太陽能可以提供無窮無盡的能源而不必擔憂二氧化碳的問題,何樂而不為呢?美國五角大樓在2007年10月的報告中則明確指出,和“向下鑽取能源”一樣,“向上鑽取能源”的工作必須立即著手開始。
響應這一號召的人似乎不少。歐洲空間局已計劃在2008年2月29日召開一次太空太陽能的會議。作為太空發電站的支援者之一,美國太空島集團已與一家歐洲公共事業公司以及印度政府就未來購買衛星系統太陽能進行了“非常積極”的商洽。
美國的另一位企業家凱文·裏德則在2007年9月提出,帛琉群島中無人居住的海倫島是修建太空太陽能小型示範項目的理想場所。利用距地球480公里的衛星,發電站能把1兆瓦的太陽能傳回地球,供1000個家庭使用。裏德認為他的公司在未來兩年內就能開始生產超輕太陽能電池,並希望能從相關製造商獲得資金支援。他預計該項目成本約為8億美元,最早能在2012年完成。 而在羅伯特·肖克這位聯合國政府間氣候變化專門委員會的未來能源專家看來,太空能源並不是虛幻得像科幻小說。肖克說,委員會2007年度報告中之所以沒有提及太空能源的潛力,是因為報告只涵蓋了2030年之前的能源問題。他說:“如果下世紀初看到人類大量使用太空能源,我不會感到驚訝,或許這個時刻還會來得更早些。”
2008年1月7日 星期一
2008年是薄膜發展關鍵年 --太陽能業者:應慎防供過於求現象

即使再生能源未來一片看好,但隱藏的風險仍是不可輕視,昱晶總經理廖國榮表示,多晶矽料源缺乏的問題短期內仍將如影隨形伴隨業者,尤其上游擴充速度遠不及中、下游擴產的速度,這將大大的影響整個產業供應鏈的產出效率。
另外,目前有76%太陽能發電是與傳統電力公司併聯合在一起,在政府的補助下由買回太陽能電力產生,如果太陽能發電擴展太快超過政府補助範圍,未來的3~5年內將會出現太陽能電力供過於求的隱憂。
太陽能業者表示, 2007~2008年缺料高峰期,多晶矽料源價格快速拉升,嚴重侵蝕許多沒有充裕料源或現貨市場料源比例過高的太陽能電池廠的獲利空間,預估該現象也會影響體質不佳的業者快速衝擊其競爭力甚致是生存。而近期包括日本、德國、美國均出現對太陽能補助縮手的現象,其實也是反應缺料,衍生政府補助造福廠商而非人民的爭議。
由於非晶矽薄膜轉換率不高,引發市場接受度的爭議持續燃燒,可以從研究單位對2009年後的走勢抱持保守的態度。依據Photon Consulting資料顯示,全球非晶矽薄膜2007年年增率達133%、2008年57%、2009~2011年年增率均維持在30%以上。
綠能總經理林和龍表示,非晶矽薄膜製程與TFT-LCD具有某種相似度,台灣優勢來自於豐沃的TFT-LCD人才。市場對非晶矽薄膜接受度及對其非晶矽薄膜各款尺寸上的偏好為何?隨著2008年有許多非晶矽薄膜廠將陸續開出產能,就可以一探究竟。
太陽能業者表示,非晶矽薄膜同樣具有供過於求的隱憂,尤其預估2010年其市場胃納量約20億瓦,但日本夏普(Sharp)宣布屆時其產能可達10億瓦,台灣也有業者喊出2010年也要達10億瓦的規模,再加上其他國家的業者,需求能否隨供給同步擴張,都是市場發展的變數。




